Are you looking for:
|
Transmission Shifter Tunnel Rubber Boot Cover Inner 5-Spd (Fiat Pininfarina 124 All) - NEW
A quality reproduction rubber shifter cover boot with foam insulation pad for all Fiat 124 Spider and Coupe with 5-speed transmission.
Reduces heat transfer from transmission and stops undercar debris from passing through the gap between shifter and interior.
Condition: NEW
New and unused.
|
Marker Light Red SIEMA (Fiat X1/9, 124, 128, 131, 850, Lancia, Ferrari, Maserati) - OE NOS
This is a F/I/A/T Factory OE red NA-spec (rectangular) marker light for the rear fenders of all 1971-88 Fiat and Lancia vehicles; including Fiat Bertone X1/9, Fiat Pininfarina 124, 131, 128, 850, Lancia Beta, Scorpion - and Ferrari vehicles.
Not a replica reproduction lens (all of which are cosmetically inferior to factory unit).
Made by SIEMA. Factory issue fitted on most Fiat and Lancia vehicles 1979-on, but can be fitted to earlier models.
Will accept an early-style Altissimo/Carello bulb holder, or a later locking-style SIEMA pigtail.
Application(s)
All models 1971-88
Condition: OE NOS
Original Equipment New Old Stock
New and Unused
|
Console Center Lower Vent Grille Left - Black (Fiat Pininfarina 124 Spider, Coupe All) - OE NOS
This is a F/I/A/T Factory OE left side grille fitted in the cut-out of Fiat and Pininfarina 124 Spider and Coupe lower center consoles.
Black in color.
These rectangular areas in the console were left blank from the factory for all Fiat 124 Coupe cars, and for 124 Spider through 1978.
In 1979, 124 Spiders began being fitted with these grilles, but most were kicked out and lost long ago.
Condition: OE NOS
Original Equipment New Old Stock
New and unused.
|
Seat Adjuster Knob Left / Right (Fiat 124 Spider 1968-78, 124 Coupe All, Lancia Beta All) - NEW
A seat adjuster knob for 1968-78 Fiat 124 Spider, 124 Coupe, and Lancia Beta series cars with lever-style release handle.
Left or right-side fitment.
Same appearance as OE.
Condition: NEW
New and unused.
|
Fuel Injection Fuel Hose KIT - High Pressure (Fiat Pininfarina 124 Spider, 131/Brava 1980-On)
IMPORTANT NOTICE! - We have chosen to offer this product in 7.9mm (5/16") high pressure hose for Fiat and Lancia L-Jet fuel injection applications, and have removed 7.5mm high pressure fuel hose from our product offerings.
We have done this because of direct experience that 7.5mm hose available on market today will prematurely deteriorate when subjected to high ethanol content.
-------------------
This is high-pressure fuel line compliant with SAE 30R9 / DIN 73379 with 7.9mm ID, suitable for use on all Fiat cars with Bosch Fuel Injection applications. 145psi working pressure with 700psi burst rating.
Please note that this fuel line is .4mm larger in diameter than stock fuel hose, and should not be used with the original "collar-lock" installation process.
Fuel Injection style hose clamps (13-15 size, available separately) are highly recommended to be used at each end of the hose that is being replaced.
--------
This is a flexible high pressure fuel line replacement kit for Fuel Injected Fiat 124 and 131 cars from late 1980 on, which uses the correct SAE 30R9 / DIN 73379 with a 7.9mm ID, 2working pressure with 700psi burst rating.
This kit includes:
- 4 x 60mm Fuel Injector Lines
- 1 x 80mm Cold Start Injector Line
- 1 x 230mm Fuel Inlet Line
- 2 x 600mm Bulk Line for Cut-to-Fit replacement of Return and Fuel Pump and Fuel Filter Lines
- 1 x 100mm Fuel Pressure Regulator Vacuum Line
- 8 High Pressure Hose Clamps.
NOTE: 12mm fuel supply hose, from tank to fuel pump, is sold separately. 3 feet is required.
Low-pressure carbureted fuel lines will bulge and weaken under the high-pressure of the fuel pump. A fuel line replacement should be performed on any Fuel Injected Fiat that has more than 75K miles or has the head and injection system off for any reason.
Condition: NEW
New and unused.
|