Are you looking for:
|
Marker Light Base Gasket - Series 2 Style (Fiat Bertone X1/9, 131, Lancia Beta + Other Italian) - OE
This is a F/I/A/T Factory OE side marker light gasket that fits between the body and rectangular marker light assembly.
May be Siema, Altissimo or Carello maker as supplies permit. All are identical in appearance.
For North America rectangular lights with exterior measurements of 109mm (4.3”)L x 39mm (1.5”)H w/70mm (2.75”) stud spacing.
Used with all model year Fiat / Bertone X1/9, Strada, 131, 128 or Lancia Beta series car. Also applicable to other Italian maker cars of the period exported to North America.
For X1/9, these are the thicker, soft rubber style as production fitted on 1979-On Fiat, Bertone X1/9
For hard plastic Series 1 style on X1/9, use 4245815.
Fits front or rear marker lights.
Condition: OE NOS
Original Equipment New Old Stock
New and unused.
|
Control Arm Rear Left (Fiat Bertone X1/9 5-Spd 1979-88, Lancia Scorpion/Montecarlo) - U8.5 / RECOND
A left rear control arm for any year Fiat or Bertone X1/9 with a 4-Spd or 5-speed transmission. Note the notch so the arm does not interfere with the extended transmission case.
Also applicable to Lancia Scorpion / Montecarlo, except does not have a bracket for the rear sway bar attachment.
The rear ball joints are prone to excessive wear, and when they go bad, the rear end of the car will do very "exciting" things, due to the ball joint allowing abrupt changes in rear toe settings. Replacement NOS ball joints are difficult to find, incredibly expensive, and very difficult to replace. The easiest solution is to replace the entire control arm.
Buy with confidence; - we will offer a LIFETIME warranty on this item. If you have any problems with the ball joint in this item during your ownership, we'll replace it free of charge.
Condition: USED / RECONDITIONED.
This item is in great shape. It hasclean-threads, original but checked OK balljoint, un-split ball joint cover, and NEW rubber bushings. Refinished and ready for install. Stock photos used for this item, yours will be similar in condition to what is shown here.
|
Clutch Line Metal Pipe - Flare Fitting Union M12x1.25 - ISO BUBBLE (Lancia Scorpion Montecarlo) - U8
A steel clutch fluid line union as applied on Lancia Scorpion / Montecarlo.
For M6 ISO bubble flare fittings / ends.
A real problem solver if you have to cut and replace a portion of a clutch line.
Condition: USED (8 of 10)
Good used condition. No issues.
|
Shifter Boot - "Pininfarina Beige" Leather (Fiat Pininfarina 124 Spider, 124 Coupe All) - OE
This is a F/I/A/T Factory leather shifter boot for Fiat and Pininfarina 124 Spider cars.
Beige tan, textured leather shifter boot as factory fitted for 1983-on Pininfarina 124 Spider, but fits all Fiat 124 Spider and Coupe cars with 4-Spd or 5-Spd manual transmission.
We are providing the difficult to find, higher imported cost shifter boot for Fiat enthusiasts who
demand original equipment performance and fitment over and above that of
a reproduction replacement grade item.
Condition: OE NOS
Original Equipment New Old Stock
New and unused.
|
Brake Clutch Master Cylinder Pivot Push Rod (Fiat Bertone X1/9, Lancia Scorpion/Montecarlo All) - U8
A brake or clutch master cylinder pivot rod for all Fiat and Bertone X1/9 and Lancia Scorpion cars.
Condition: USED (8 of 10)
Good used condition, no wear or slop in the pivot hole.
|