Are you looking for:
|
Wheel Bearing Retainer Ring - Front/Rear 53mm HEX (Fiat X1/9 4-Spd, 128, Yugo, Lancia Scorpion Front) - EARLY TYPE
A wheel bearing retainer ring for all 4-Spd Fiat X1/9s, all Fiat 128, Yugo, and Lancia Scorpion.
Requires 53mm Hex tool for removal and install, sold separately.
Sometimes referred to as an axle bearing lockring.
60mm OD.
Application(s):
Front + Rear wheels:
Fiat X1/9 4-Spd (1974-78)
Fiat 128 All (1971-79)
Yugo All (w/Manual transmission)
Front wheels only:
Lancia Scorpion
Rear wheels only:
Yugo All (w/Automatic transmission)
Condition: NEW
New and unused.
|
Trans Bearing Input Shaft (Fiat 850 All), Rear Cluster Layshaft 5th / Reverse 52mm (Fiat 124 4/5-Spd 1967-69) - OE
Factory OE bearing applicable to Fiat 850 transaxles, and 124 4-Spd and 5-Spd transmissions. 52mm OD.
Application(s):
Fiat 850: Inner front on input cluster shaft.
Fiat 124 4-Spd: Cluster support bearing
Fiat 124 5-Spd: 5th Gear countershaft rear bearing 1968-69.
Condition: OE NOS
Original Equipment New Old Stock.
New and Unused.
|
Lug Bolt SET 30mm - FIAT 80 - 12x1.25 for Steel Wheels SET 16x (Fiat 124, 131, 128, 1100/1200/1500) - OE / RENEWED
This is a Factory OE lug bolt set for Fiat 124, 128 and 131 cars. Right hand thread, also used for two of the wheels on Fiat 1100/1200/1500 cars.
16x pieces included.
19mm head, M12x1.25 thread, with 30mm length under the tapered head. Correct factory markings.
Condition: OE / RENEWED
Either Original Equipment New Old Stock as supplies permit, or clean refinished used units, freshly plated in yellow zinc.
|
Wheel Bearing Retainer Ring - Front/Rear 45mm HEX (Fiat X1/9 4-Spd, 128, Yugo, Lancia Scorpion Front) - LATE-STYLE
This is a Factory OE wheel bearing retainer ring for use on 4-Spd style upright/carrier assemblies in 1973-78 Fiat X19, 128 and Yugo cars.
Used on front and rear upright/carrier assemblies.
===> REQUIRES Axle HUB COLLAR to engage this style of Lockring's "Built-In" SEAL. See attached photo.<===
Do not use with separate V-Ring seal.
Requires small 45mm hex ring tool Part Number 34187) available separately.
Application(s):
Front + Rear wheels:
Fiat X1/9 4-Speed (1974-78)
Fiat 128 All (1971-79)
Front wheels only:
Lancia Scorpion
Montecarlo
Yugo
Condition: OE
Original Equipment New Old Stock
New and unused.
|
Turn Signal Assembly Front PAIR (Fiat Pininfarina 124 Spider, Bertone X1/9, 131, 128, Lancia 1975-On) - OE NOS
This is a F/I/A/T Factory OE Altissimo pair of turn signal assemblies; with lens, boot, and harness; for 1975-85 Fiat 124 Spider, 1979-88 Fiat and Bertone X1/9s, 131, and Brava cars.
Body and lens is applicable and identical across all model years.
Wiring harness with bullet-style connector for 1979-on cars can easily retrofit to spade terminals 1975-78 vehicles.
Please note: This pair includes two RIGHT-side units.
These mount identically within the left and right-side bumper pockets. The only difference is that the wiring lead pigtail exits from the top of the housing instead of the bottom on one side. This is completely unnoticable when installed.
Made by Altissimo.
Application(s):
Fiat Pininfarina 124 Spider All (1975-85)
Fiat Bertone X1/9 1976-On North America
Fiat 131 Brava All North America
Fiat 128 1975-On North America
Lancia Beta All North America
Lancia Scorpion All North America
Condition: OE NOS
Original Equipment New Old Stock.
New and unused.
|