Are you looking for:
|
Wing Window Quarter Window Glass Left - HOLE / TINTED / North America (Fiat Bertone X19 1980-88 + All) - OE NOS
This is a Factory OE left (NA-spec driver side) Wing Vent Glass by Saint Gobain for late-model Fiat Bertone X1/9s from 1980 - 88. This glass is tinted to North American spec and has a hole for a "pass-through" style Vitalone mirror. This item can be fit to any model year Fiat or Bertone X1/9.
Condition: OE NOS
Original Equipment New Old Stock
New and unused.
|
Fuel Injection Thermo-Time Switch (Fiat Bertone X1/9, 124 Spider, Brava, Strada, Lancia Beta) - U8.5 TESTED
This is a thermo-time sensor for 1980 and later Fiat and Bertone X1/9s, Fiat and Pininfarina 124 Spider, Brava, Strada and Lancia Beta with L-Jet Bosch electronic fuel injection.
A critical component to the cold start functions on your FI car.
Condition: USED and TESTED (8.5 of 10)
Cleaned and tested to be within spec on all functions. This item will be warranted and replaced if found defective within 30 days.
|
Trans Bearing Center Cluster Lay Shaft (Fiat Pininfarina 124 Spider Coupe All 5-Spd+4-Spd, 1500 Cabriolet) - NEW
A high quality roller bearing assembly located as the center bearing on the cluster shaft in all Fiat 124 Spider and Coupe 5-Spd and 4-Spd transmissions. Also applicable to 1500 Cabriolet.
Condition: NEW
New and Unused.
|
Wheel Bearing Retainer Ring Tool - 53mm "Early" Style (Fiat X1/9 1973-78, 128, Yugo, Lancia Scorpion Front) - OE
High quality carrier bearing retaining ring removal / installation tool for all 4-Spd Fiat X1/9s, all Fiat 128, Yugo, and Lancia Scorpion.
Designed specifically for the 60mm OD brass lockrings securing wheel bearings on the above vehicles.
Note: Not applicable to 5-Spd Fiat and Bertone X1/9s which have larger bearings and retainer rings. May be 1/2" or 3/4" drive as supplies permit.
Proper usage of this tool avoids harm to bearing hubs and prevents destruction of brass retainer rings that lock in wheel bearings.
Without this tool, the bearings' retaining rings suffer under removal attempts using common hand tools that usually waste hours of frustration and often harm carrier components.
For years, Fiat and Lancia owners have been forced to remove their retainer rings using hand tools.
The removal tools for Fiat X1/9 or Lancia retainer rings were very difficult items to find.
Midwest Bayless now offers the right tool for the job - just as nature intended.
Application(s):
Front + Rear wheels:
Fiat X1/9 4-Spd (1974-78)
Fiat 128 All (1971-79)
Yugo All (w/Manual transmission)
Front wheels only:
Lancia Scorpion
Rear wheels only:
Yugo All (w/Automatic transmission)
Condition: NEW
New and unused.
|
Camshaft DOHC Exhaust Wide Lobe w/Gear 5/53 Timing (Fiat Pininfarina 124, 131 1974-On, Lancia Beta 1975-78) - OE
This is a Factory OE North American-spec (53/5 - 5/53) exhaust cam for Fiat DOHC engines as fitted to Fiat and Pininfarina 124, Fiat 131, and 1975-78 Lancia Beta with cam-box-mounted distributor.
This is the late style with wide lobes for maximum life. The larger lobe spreads the load of the valve spring across the entire face of the shim, leading to longer life for both the cam and the shims.
Condition: OE NOS
Original Equipment New Old Stock
New and unused. Discoloration is due to packing agent, not oxidation.
|