Are you looking for:
|
Brake Caliper - SET - Front Left + Right (Fiat Pininfarina 124, X1/9, 128, 131, Yugo, Scorpion/Montcarlo) - NEW
A pair of brake calipers for front left (driver) and right (passenger) as factory fitted on the following Fiat, Lancia, Pininfarina, and Bertone cars.
These caliper assemblies are top quality units with new precision machined castings.
Application(s):
- Fiat / Pininfarina 124 All (1967-84)
- Fiat Bertone X1/9 5-Spd (1979-88)
- Fiat 128 All (1971-79)
- Fiat 131 / Brava All (1975-82)
- Fiat Strada / Ritmo Series 1 1979-82
- Yugo (except automatic)
- Lancia Scorpion / Montecarlo
- Fiat X1/9 4-Spd (1973-78)
(REQUIRES ALTERNATE 3/8-24 BANJO BOLTS)
No core return required on calipers.
Condition: NEW
New and unused.
|
Piston Set 85.0mm DOHC - 10:1 High Compression FORGED (Fiat Pininfarina 124, 131, Lancia Beta All 1.8/2.0) - NEW
Specifically designed for Midwest-Bayless!
This is a set of four American made, lightweight forged aluminum pistons, suitable for all Fiat or Lancia DOHC racing or hot-street application in 132-series engines (1756cc / 1996cc).
Yields approximately 9.8:1 compression with 2.0. A bit higher with 1.8L. A good target for street use, these work great with mid range and high octane (91 or 93) pump gasoline and provide a big increase in performance over the stock North America low compression flat top units.
Specifications:
- Diameter: 85.0mm
- Compression Height: 38.45mm
- Dome Height: 6mm
- Recommended Skirt Clearance: .076mm (.003 in)
- Weight: 385g
These pistons use three rings. Piston rings, slip-fit 22mm pins and retainer circlips included.
NOTE: These are SPECIAL ORDER items that may have up to 4 weeks of production time. Please inquire for time to delivery. No refunds or returns.
Other bore sizes are available between 84.0mm and 86.0mm, however 85.0mm is the optimal oversize bore for all 1800cc or 2000cc motors. If you require alternate bore size, please call before ordering.
Condition: NEW
|
Wheel Bearing Retainer Ring - Front/Rear 53mm HEX (Fiat X1/9 4-Spd, 128, Yugo, Lancia Scorpion Front) - EARLY TYPE
A wheel bearing retainer ring for all 4-Spd Fiat X1/9s, all Fiat 128, Yugo, and Lancia Scorpion.
Requires 53mm Hex tool for removal and install, sold separately.
Sometimes referred to as an axle bearing lockring.
60mm OD.
Application(s):
Front + Rear wheels:
Fiat X1/9 4-Spd (1974-78)
Fiat 128 All (1971-79)
Yugo All (w/Manual transmission)
Front wheels only:
Lancia Scorpion
Rear wheels only:
Yugo All (w/Automatic transmission)
Condition: NEW
New and unused.
|
Fender Rear Right Quarter Panel - Repair Patch Panel - Forward Portion (Fiat Pininfarina 124 Spider All) - NEW
This is a patch panel for the right rear (NA-spec passenger side) fender on all Fiat 124 Spider cars.
Fits between fender arch and door. Also known as "rear rocker" area.
Heavy gauge steel with correct fender arch contour. 12" tall.
Condition: NEW
New and unused.
|
Lug Bolt SET 30mm - FIAT 80 - 12x1.25 for Steel Wheels SET 16x (Fiat 124, 131, 128, 1100/1200/1500) - OE / RENEWED
This is a Factory OE lug bolt set for Fiat 124, 128 and 131 cars. Right hand thread, also used for two of the wheels on Fiat 1100/1200/1500 cars.
16x pieces included.
19mm head, M12x1.25 thread, with 30mm length under the tapered head. Correct factory markings.
Condition: OE / RENEWED
Either Original Equipment New Old Stock as supplies permit, or clean refinished used units, freshly plated in yellow zinc.
|